How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (2024)

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (1)

  • ibtinc

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (2)

A V-belt’s purpose is to transmit energy between two components. What makes a V-belt pulley stand out from other types of pulleys, such as a round belt or flat pulley, are the V-shaped grooves of the pulley; these grooves guide the belt and allow it to gain traction.

The number one cause of a power transmission belt failure is improper tensioning. In order to ensure a long and efficient belt operation, you must properly learn how to tension a V-belt regularly.

If a V-belt is too loose, there can be slippage, rapid belt or sheave wear, and, ultimately, loss of both energy and productivity. Conversely, if there is too much V-belt tension, the excess strain on the belts, bearings, and shafts can cause premature wear of these components.

Proper V-belt tension is the lowest tension at which the belt won’t slip or squeal under peak load. However, there is still a wide range of tension between these two extremes in which a drive will operate sufficiently. The primary goal of learning how to tension a V-belt is to find this happy tension medium.

Important Note: Never apply belt dressing, as this will damage the belt and cause early failure. Always keep the drive free of foreign material which might cause slippage or damage to the belt and sheave surfaces.

#1 ─ HOW TO TENSION A V-BELT WITH THE FORCE/DEFLECTION METHOD

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (3)

This is the preferred method of our customers.

This V-belt tensioning method relies on a Pencil Gauge Tool and the mathematical standards laid out in this V-belt tensioning table.

  1. Measure the span length “K” of your drive (See Figure 1).
  2. Slide the large O-ring to the recommended deflection distance on
    the scale, and slide the small O-ring up against the barrel of the gauge as shown in Figure 2.
  3. Place the large end of the tool onto the belt at the center of the span. Apply a sufficient force to deflect the belt until the large O-ring is in-line with the other belts. If this is a single-belt drive, use a straight-edge or taught string for a “starting point” reference.
  4. Then, release the pressure and read the deflection force from the position of the small O-ring on the plunger scale, as shown in Figure 2.
  5. Compare this force with the value given in the V-belt tensioning table. If the force is below the recommended value, increase the drive center distance to provide greater belt tension. Reduce the center distance if there is too much force.
  6. For example, for a 100″ span, the deflection would be 100/64″, or approximately, 1½”.
How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (4)

PENCIL GAUGE PROS: Inexpensive ─ Precise

PENCIL GAUGE CONS: Time-Consuming ─ Tedious

#2 ─ HOW TO TENSION A V-BELT USING A BELT FREQUENCY METER

This method is IBT’s recommended choice for precision V-belt tensioning and time efficiency. Pristine accuracy will best help you achieve belt longevity, ultimately saving you money.

  1. The first step is to load the belt’s span and mass data into the meter. Mass data can be obtained from any belt manufacturer and varies between them.
  2. Aim the sensor as close to the center of a selected belt span as possible in order to get the most accurate tension reading. The best practice is to orient the sensor with the long edge parallel to the belt centerline with approximately a ½˝ gap. Using too short of a span could yield false tension readings that may be much higher than the actual belt tension, due to the effects of belt stiffness.
    • If the top surface of the belt is not easily reachable, beaming the sensor against the edge of the belt functions equally as well.
  3. Tap the belt, using the handle of a small tool or something similar, to make it vibrate for a reading. The meter will report the belt tension in units of force.

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (5)

Here are some procedures and “best” practices that may ease use or help increase the reliability of your belt tensioning efforts:

  • On new installations, hand rotate the system at least one full revolution of the belt in order to seat and normalize the components.
  • When tensioning different V-belts, use a single belt toward the center. Banded belts are to be treated as a single unit with the belt mass constant calculated as a multiple of the single belt value.
  • Take three successive readings for consistency purposes. If the readings vary by more than 10%, reassess your measurement technique.
  • The meter will not give a measurement reading for a belt under extremely low tension. If the meter is not responding, simply increase the drive tensioning until the meter responds.

METER PROS: Quick ─ Easy ─ Accurate ─ Pays For Itself

METER CONS: Expensive Initial Cost

#3 ─ HOW TO TENSION A V-BELT USING THE “THUMB TEST”

The best way to do this method? Don’t.

We mention the “thumb test” method (using your hand or thumb to apply pressure to the belt as a way to judge whether or not it has the correct amount of tension) because many traditional businesses still practice this type of V-belt tensioning.

When it comes to getting the most life out of your belts and maximizing the operational efficiency of your business, we do not recommend that anyone rely on anything less than the precision tensioning tools mentioned above in methods #2 and #3.

While the “pros” of this method include the initial money and time savings gained from this simple procedure, as opposed to investing in a tensioning tool, the cost build-up of having to replace your belts frequently will ultimately overshadow this, consequently increasing downtime from belt failure.

THUMB TEST PROS: Inexpensive Initial Cost ─ Fast ─ Easy

THUMB TEST CONS: Unreliable ─ Inaccurate

V-Belt Pencil-Type Tension Gauge

V-Belt Frequency Meter

ContiTech offers a high-quality tension testing tool. Designed for the tension testing of a drive with two or more belts, this pocket-sized tool measures V-belts from 10” to 170” and up to 35 pounds of tension. Measure belt span and measure the force required to deflect any one of the belts 1/64” for every inch of span length.The TensionRite® Meter, from the trusted brand of Continental ContiTech, provides a simple, repeatable and reliable method for tensioning belts using optical technology. It is capable of both measuring all belt styles, from all manufacturers, with vibration frequencies between 10Hz and 400Hz.


About IBT’S Industrial Rubber Products and Solutions

The IRPG team at IBT Industrial Solutions fabricates and services conveyor belts every day—offering both heavyweight and lightweight options—for all types of industries. They also cut and crimp a wide variety of industrial hydraulic and pneumatic hoses at our KC Hose Shop facility, which is a ContiTech STAR facility, exceeding criteria for cleanliness and hose safety as set forth by NAHAD and certified by Underwriters Laboratory. We have the inventory and expertise to service all your belting and hose needs.

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (6)

Shop All of Our V-Belt Solutions

Check out ShopIBT.com to find the right belt for your needs!

Share:

Recent News

Wing Pulleys : What They Are and How They Work

What is a Flex Coupling?

5 Advantages of Brushless Motors

Essential Fall Protection – Making Safety a Priority

Why Split Bearings Save You Time

Automation in Bag Fillers – What You Need to Know

What’s the Difference Between Double and Single Row Bearings?

4 Types of Bucket Elevators

Electric Motors Explained – A Helpful Guide

How Bearings Keep Your Food Safe

10 Types of Specialty Belting That Boost Efficiency

Helpful Solutions for 4 Bulk Material Handling Problems

What to Know About Electric Motor Bearings

The Benefits of the Right Gearbox

Get in touch for help and information

Our head office address:

9400 W 55th St, Merriam, KS 66203

Call for help:

(913) 428-2858

How to Tension a V-Belt (& How Not to) | IBT Industrial Solutions (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Terrell Hackett

Last Updated:

Views: 5394

Rating: 4.1 / 5 (52 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Terrell Hackett

Birthday: 1992-03-17

Address: Suite 453 459 Gibson Squares, East Adriane, AK 71925-5692

Phone: +21811810803470

Job: Chief Representative

Hobby: Board games, Rock climbing, Ghost hunting, Origami, Kabaddi, Mushroom hunting, Gaming

Introduction: My name is Terrell Hackett, I am a gleaming, brainy, courageous, helpful, healthy, cooperative, graceful person who loves writing and wants to share my knowledge and understanding with you.